MEI Premium Range of Automatic Slack Adjusters

Click Here to Learn More

Madras Engineering Industries

Click Here to Learn More

MEI Air Disc Brake Range

Click Here to Learn More

MEI Announce their New Range

Of Air Disc Brake Calipers

.
adbhome6 
.
adb5points

 

 

Designed In Our Multi Million Pound Research and Development Centre

.

 

All MEI Facilities are ISO/TS16949 & ISO9001 Certified

 .

The pistons and tappet heads have an important function in the brake caliper as they clamp the pads to the disc, and whilst the tappet heads are rarely damaged, the seals behind them have to perform under difficult conditions, particularly heat and dirt.

1. Checking the condition of the tappet seals is important during a regular vehicle inspection, but Inspection of seal is difficult they can be without extending the piston difficult to inspect without removing the pads. However, shining a torch into the area between the inboard pad and the housing can give a good initial view of the seals. The seal in Fig.1 has heat damage, which should be possible to detect without removing the pads. However, a tappet seal in this condition must be replaced immediately in order to prevent further damage to the brake.

Fig 1 tappet 1

 

2. It is difficult to see the tappet seal if the piston is not extended. Therefore, to carry out a proper inspection, adjust the pistons out so that the seal is fully visible. Take care: Limit the extension to no more than 30mm from the front cover! (Fig.2)

 Fig 2 tappet 2b 

3. If the brake has seen higher temperatures through sticking guide sleeves, it is important to check for other effects and issues caused by this. The main one is the possibility of damaged tappet boots through excessive heat (Fig.3).

 Fig 3 tappet 3 

 

4. In Fig.4, the primary seals have been removed from the front cover, showing a good example of a damaged tappet boot (right hand) with water/dirt discolouring the secondary seal, putting the brake at risk of water ingress if the primary seal is not changed. The left hand seal is OK and highlights the difference in colour.

Fig 4 tappet 4

 

5. After removing the damaged seal, the piston threads can be carefully cleaned with a small wire brush (Fig.5), so long as dirt and  corrosion is not excessive. However, take care to assess the condition of the secondary seal and make sure there are clean threads underneath the seal. If corrosion extends under the secondary seal, the caliper should be replaced.

 Fig 5  tappet 5

 

6. Tappet heads should be carefully removed with the correct service tool as damage to the piston threads will prevent the brake from being adjusted for the fitment of new pads (Fig.6).

 Fig 6 tappet 6 

 

7. If necessary, remove the secondary seal to make a more detailed assessment and then replace with a new secondary seal from the repair kit (Fig.7).

 Fig 7  tappet 7

 

8. After removing the tappet seal, check the cover plate – if the sealing interface is damaged or corroded, then the caliper should be  replaced. On re-assembly, lubricate the piston threads with the white grease supplied in the kit (5F1500) (Fig.8).

 Fig 8  tappet 8

 

9. It is important to lubricate the face of the tappet head that touches the end face of the piston, as the piston must be free to rotate while the tappet head is static. Use black (high pressure) grease supplied in the
kit (5F1505), (Fig.9 and 10).

Fig 9  tappet 9 Fig 10 tappet 10 

 

10. Lastly, for re-assembly, use of the correct tool makes for accurate refitting of the tappet seal and tappet head (Fig.11).

 Fig 11  Tappet 11

 

11. Note that the tappet heads and seals can be replaced with the caliper either on or off the vehicle using the MEI tool kit (see the MEI website for full instructions). Tappet Heads and seals are often overlooked and need to be part of the regular vehicle check. Ensure good quality repair kits and the correct service tools are used for the job. It is a straightforward repair, but care must be taken to assess whether corrosion has taken hold or not. The threads need to be able to be cleaned with hand tools so that the pistons wind in and out without excessive force.

 

If you would like to receive our newsletters please complete the following information.
Terms and Conditions

modsearch

modadb

modslack